Your signature on a shop drawing is not paperwork. It is permission to cut glass that cannot be uncut. That is why we send the drawing at all. Once you approve it, the panels get cut, drilled, notched, and tempered to exactly what is on that page — and tempered glass cannot be trimmed, re-drilled, or patched afterward. A mistake caught on paper costs a pencil line. The same mistake caught on install day costs a new panel and a new wait. You do not need to be a glazier to read one of these drawings well. You need to check four things, in order: which panel is which, the dimensions, the swing, and the hardware and glass spec. Here is how we walk a Los Angeles homeowner or contractor through it before anyone signs.
Start with the labels: which panel is which
Every panel on the drawing has a label — P1, P2, Door, Fixed, Return, and so on — and an elevation view that shows the enclosure or railing the way you will stand in front of it. Before you look at a single number, match the drawing to the room. Stand where the drawing is viewed from and confirm the view direction noted on the page: most elevations are drawn viewed from outside the shower, outside the railing, or from a stated side of the opening. Left and right flip completely if you read the view backwards, and that one confusion is behind more wrong-hinge-side approvals than any measuring error. If the drawing shows a door on the left and your door is on the right, stop there. Nothing else on the page can be trusted until the view matches the room.
Dimensions: opening size is not glass size
This is the part most people misread, and it is not their fault. A shop drawing carries two kinds of numbers. The opening dimensions are the finished hole the glass has to fill — curb to wall, wall to wall, floor to ceiling line. The glass dimensions are smaller, because real glass needs clearance, setting space, and hardware deductions taken off the opening. If the glass numbers look a fraction smaller than the numbers you measured with your own tape, that is usually correct, not a mistake. What you should check is the opening itself: does the width and height on the drawing match the finished opening as it stands today — tile done, curb done, walls done? Glass is measured to the finished surfaces, not to the framing that was there last month.
Check the fractions, not just the whole inches, and check height in more than one place if the drawing shows it. Real openings are rarely perfectly square or plumb. A good drawing shows where each height was taken, notes an out-of-square or sloped curb or ceiling when there is one, and shapes the glass to it. If your shower has a bench, a knee wall, a sloped ceiling, or a notch around a fixture, find that feature on the drawing. If it is not drawn, it is not ordered. Our shower glass drawings call out benches, notches, and out-of-plumb walls for exactly this reason — the glass has to be cut to the opening you actually have.
Swing and hinge side: draw the door moving in your head
Find the door panel and answer three questions. Which side are the hinges on? Which way does the door swing — into the shower or out into the room, or both if it is drawn that way? And when it swings, what does it hit? Play it through in the actual room: an out-swinging shower door needs clear floor and cannot strike a vanity, a toilet, or a towel bar; a door hinged off a fixed panel moves differently than a door hinged off the wall, and the drawing shows which one you are getting with its hinge symbols and the small arc or note that marks the swing. Then check the handle side against the shower controls and the handheld: you want to reach the handle, step in, and reach the controls without the door fighting you. If you stand in the bathroom and the drawing's door opens the opposite way from what you pictured, say so before you sign — moving a hinge on paper is free, and after tempering it means a new door.
Hardware: count it, place it, and confirm the finish
- Hinges vs. clamps vs. channel: hinges belong on the door only. Fixed panels are held by clamps or channel, and the drawing should show which — they look different, seal differently, and read differently on a frameless enclosure. If a clamp symbol sits on the door panel, ask why.
- Count and location: count the clamps and hinges drawn and compare them to the panel sizes. A tall or wide fixed panel needs support at its real locations, not a single symbol standing in for all of them. Note where each one sits — near the ends and spaced along the run is what you want to see described.
- Handle or pull: confirm the type — knob, ladder pull, or back-to-back pull — its length, and its height and distance from the edge as drawn. Holes for handles and knobs are drilled before tempering, so the hole on the drawing is the hole you live with.
- Finish, in words: the finish name on the drawing is what gets ordered — chrome, brushed nickel, matte black, and the rest are not interchangeable, and dark bronze and black read as the same family but should still match the words you approved and the fixtures already in the room.
- Clear parts are parts: sweeps, seals, and drip rails on a shower door are clear, and they should be listed or noted. If a detail matters to you and it is not on the drawing or in its notes, it is not in the order.
Glass spec: thickness, type, and treatment
Last, read the glass callout itself. It should state the thickness, whether the glass is clear or low-iron, tempered or laminated where the location requires it, and any pattern, frost, or coating by surface when one is specified. Thickness follows the job — door weight, panel size, and mounting all feed it — so do not approve a thinner or thicker panel than the one you discussed without asking what changed. If a textured or rain-pattern panel is in the order, confirm which face the texture sits on and which way it faces in the room; that orientation is decided on this page, not on install day. Edge work should be noted too — polished edges where hands and eyes meet the glass every day.
Five checks before you sign
- The elevation view matches the room when you stand in the stated viewing position.
- The opening width and height match the finished opening today, fractions included.
- The door's hinge side and swing clear everything in the room and match how you will use it.
- Every hinge, clamp, handle, hole, and finish on the page is the one you chose — counted, not assumed.
- The glass thickness, type, and texture orientation read exactly as discussed.
If all five hold, sign it and keep a copy. If one does not, mark the drawing up, send a photo of the markup, and ask for a revised sheet — a clean revision you re-check beats a verbal promise every time. And take your time with it. A good shop will rather redraw once than remake glass, because both of you pay for the remake in time.
The short answer
Read a shop drawing as the cutting order it is: match the view to the room, confirm the finished opening, walk the door swing in your head, count the hardware and confirm the finish in words, and verify the glass spec — before you sign. Approval locks the glass. Five careful minutes on paper are what keep install day uneventful.
Have a shop drawing in front of you and want a second set of eyes before you approve it? Call or text Versa Glass Co. at (310) 847-9746 with a photo of the drawing and a photo of the opening. We will walk the dimensions, swing, and hardware with you before anything is cut.
Get a Quote Call (310) 847-9746