The closer you cannot see is the one doing the most work under the door. On a framed storefront door, the closer question is easy — a surface closer bolts to the frame and the door, and you adjust it with a screwdriver. An all-glass door has no frame to bolt to and no stile to hide anything in. The glass itself is the structure, carried by a top and bottom rail or patch fittings, and whatever controls it has to live in the header above or in the floor below. That choice — overhead concealed closer or floor spring — is made before the glass is cut, because the fittings, the pivot points, and the floor work are different. Pick it late and you are re-cutting glass or cutting a floor you did not plan to cut. Here is how we decide it on Los Angeles commercial and high-end interior work.
What each one actually is
An overhead concealed closer sits in the header or transom bar above the door. A spindle drops down into the top patch fitting, and the door pivots on that spindle at the top and a pivot point at the bottom. The closer body is hidden, the look is clean, and no hole is cut in the floor. A floor spring is the opposite layout: a cast body set into a cement case in the floor, with its spindle rising into the bottom rail or patch. The top is just a pivot in the header. The floor spring carries the door's weight on the floor — where weight wants to go — and controls closing from below. A surface-mounted closer is the third name people bring up, and on a true all-glass door it is usually the wrong answer: there is no frame leaf to mount it to cleanly, and the arm and body wreck the all-glass look the door was bought for.
Double action, single action, and hold-open
Most all-glass entrance and interior doors need to swing both ways — in and out — and return to center. That is double action, and both systems can do it, but you have to order the right version. A single-action closer on a door people push from both sides will be forced, and forced hardware fails early. Hold-open is the other decision to make on paper: do you want the door to stay open at 90 degrees for deliveries and open-house traffic, or must it always self-close and latch for a fire, smoke, or security requirement? A hold-open floor spring or closer holds mechanically at the set angle. A non-hold-open version never stays open on its own. Neither is better — the wrong one for the use is the problem. A retail door that will not stay open gets propped, and a propped door bends pivots. A rated door with hold-open that is not tied to an alarm is an inspection failure.
Weight and size decide more than preference does
All-glass doors are heavy. A tall 1/2-inch tempered door with rails can push well past what a light overhead closer is rated to control, and an undersized closer does not fail politely — the door slams, drifts off center, stops latching, and chews up its pivots. Floor springs are built in heavier duty classes and carry the load on the floor bearing, so for very wide, very tall, or high-traffic doors they are usually the honest choice. For a standard interior all-glass door in an office or a boutique, a properly rated overhead concealed closer is enough and avoids the floor work entirely. The rule is simple: match the closer class to the actual door weight and width and the traffic count, not to the rendering. Our storefronts and commercial glass work starts with that weight check for exactly this reason.
The floor decides whether a floor spring is even possible
- Slab and depth: a floor spring needs a pocket cut into the floor for its cement case. In a slab you can cut, that is routine work planned before flooring. Over a post-tension slab, a raised floor, radiant heat, or a floor you cannot cut — a historic tile floor, a landlord who forbids it — it may be off the table entirely.
- Water and dirt: a body in the floor lives where mop water, rain at an entrance, and grit go. Good installs seal the case and use a cover plate that sits flush; neglected ones fill with water and corrode from below where nobody looks.
- Threshold and trip: the cover plate must finish flush. A plate that sits proud or rocks is a trip edge at the busiest point in the building, and an ADA problem at an entrance.
- Timing: the case has to be set level and on centerline before the finished floor closes around it. Retrofitting a floor spring into a finished floor is doable, but it is demolition, not a service call.
Service: what happens in year three
Both systems are adjustable for closing speed and latching speed, and both eventually need service — seals age, oil thins, doors get knocked off center. The difference is access. An overhead concealed closer is reached from above: drop the cover or work through the header, swap the body without touching the floor or, in many cases, re-cutting anything. A floor spring is reached by lifting the door off its spindle and opening the cover plate; the body can be serviced or replaced from the case, but the door — that heavy sheet of glass — has to be handled to get there, and the floor finish around the plate is in play every time. Neither is a reason by itself to choose one over the other. It is a reason to install the one you pick correctly the first time: centered, level, and rated, because every service visit on an all-glass door is a two-person glass-handling job, not a ladder-and-screwdriver job.
So which one belongs on your door?
- Choose an overhead concealed closer when the door is standard weight, the floor cannot or should not be cut, the header has room for the body, and a clean floor line matters — most interior office, showroom, and suite doors land here.
- Choose a floor spring when the door is oversized or heavy, traffic is high and two-way all day, the floor is being built or opened anyway, and you want the weight carried on the floor with the heaviest-duty control available — most flagship entrances land here.
- Decide before fabrication either way: the top and bottom fittings, pivot locations, and glass cutouts differ, and tempered glass cannot be re-notched after the fact.
If you are replacing a failed unit on an existing door, stay with the system the door was built for unless there is a structural reason to change — converting systems means new fittings, new glass work, and floor or header work, which is a rebuild, not a repair.
The short answer
There is no closer bolted to an all-glass door. There is a closer in the header or a spring in the floor, and the right one follows the door's weight, the traffic, whether it must hold open or always close, and whether your floor can take the case. Decide it before the glass is cut, size it honestly, and the door will close the same way in year five as it did on install day.
Planning an all-glass door, or fighting one that slams, drifts, or will not stay open? Call or text Versa Glass Co. at (310) 847-9746 with the door size, a photo of the top and bottom fittings, and a photo of the floor at the door. We will tell you which system the door needs — and which one it can actually take.
Get a Quote Call (310) 847-9746